2013年12月17日星期二

Configuring CAR on a Layer 2 Port

The Huawei ME60 /40E supports configuration of traffic policing in both inbound and outbound directions on Layer 2 interfaces.
You can configure traffic policing for the NE80E/40E only on the physical GE and Ethernet interfaces.
Run:
system-view
The system view is displayed.
Run:
interface { ethernet | gigabitethernet } interface-number
The interface view is displayed.
Run:
portswitch
The Layer 2 interface view is displayed.
Run:
port default vlan vlan-id
A Layer 2 interface is added to a specified VLAN.
NOTE:
Please confirm the specified VLAN has been created before running this command.
Run:
port trunk allow-pass vlan { { vlan-id1 [ to vlan-id2 ] } & <1-10> | all }
The IDs of the VLANs allowed by the current interface are specified.
Run:
qos car { cir cir-value [ pir pir-value] } [ cbs cbs-value pbs pbs-value ] [ green { discard | pass [ service-class class color color ] } | yellow { discard | pass [ service-class class color color ] } | red { discard | pass [ service-class class color color ] } ]* { inbound | outbound } [ vlan { vlan-id1 [ to vlan-id2 ] &<1-10> } ]
 NOTE:

CAR is configured on an interface. The parameter [ vlan { vlan-id1 [ to vlan-id2 ] &<1-10> } ] takes effect only on layer 2 interfaces, and VLAN ID must be configured. When this command is configured  ME60 on a layer 3 interface, however, VLAN ID cannot be configured.

2013年12月16日星期一

Configuration file of ME60 A

 sysname Huawei ME60A
#
 set board-type slot 5 tunnel
#
interface GigabitEthernet2/0/0
 undo shutdown
 ip address 10.1.1.2 255.255.255.0
#
interface Pos1/0/0
 undo shutdown
 link-protocol ppp
 ip address 20.1.1.1 255.255.255.0
#
interface LoopBack1
 ip address 1.1.1.9 255.255.255.255
target-board 5
binding tunnel gre
#
interface Tunnel5/0/1
 tunnel-protocol gre
 ip address 40.1.1.1 255.255.255.0
 source LoopBack1
 destination 2.2.2.9
#
ospf 1
 area 0.0.0.0
  network 20.1.1.0 0.0.0.255
  network 1.1.1.9 0.0.0.0
#
ip route-static 10.2.1.0 255.255.255.0 Tunnel5/0/1
#
return
Configuration file of ME60 B

#
 sysname ME60B
#
interface Pos1/0/0
 undo shutdown
 link-protocol ppp
 ip address 20.1.1.2 255.255.255.0
#
interface Pos2/0/0
 undo shutdown
 link-protocol ppp
 ip address 30.1.1.1 255.255.255.0
#
ospf 1
 area 0.0.0.0
  network 20.1.1.0 0.0.0.255
  network 30.1.1.0 0.0.0.255
#
return
Configuration file of ME60 C

#
 sysname ME60C
#
 set board-type slot 5 tunnel
#
interface GigabitEthernet2/0/0
 undo shutdown
 ip address 10.2.1.2 255.255.255.0
#
interface Pos1/0/0
 undo shutdown
 link-protocol ppp
 ip address 30.1.1.2 255.255.255.0
#
interface LoopBack1
ip address 2.2.2.9 255.255.255.255
target-board 5
binding tunnel gre
#
interface Tunnel5/0/1
 tunnel-protocol gre
 ip address 40.1.1.2 255.255.255.0
 source LoopBack1
 destination 1.1.1.9
#
ospf 1
 area 0.0.0.0
  network 30.1.1.0 0.0.0.255
  network 2.2.2.9 0.0.0.0
#
ip route-static 10.1.1.0 255.255.255.0 Tunnel5/0/1
#

ME60 Return

Configuring a Tunnel Interface on Huawei AR3260

AR3260 Series routers are designed to provide secure unified voice and data communication with exceptional performance and scalability to meet the demands of today’s enterprise requirements.
Run:
system-view
The system view is displayed.
Run:
interface tunnel interface-number
A tunnel interface is created and the tunnel interface view is displayed.
Run:
tunnel-protocol gre
The tunnel encapsulation mode is set to GRE.
Run:
source { source-ip-address | interface-type interface-number }
The source address or source interface is configured for the tunnel interface.
Run:
destination [ vpn-instance vpn-instance-name ] dest-ip-address
The destination address is configured for the tunnel interface.
Run:
mtu mtu
The MTU of the interface is set.
Run:
description text
The description of the current tunnel interface is set.
Run:
ip address ip-address { mask | mask-length } [ sub ]
An IP address is configured for the interface.
Run:
ip address unnumbered interface interface-type interface-number
The tunnel interface is configured as an IP unnumbered interface.

The Huawei AR3260  routers integrate routing, switching, 3G, voice, and security functions. It utilizes a multi-core CPU and non-blocking switching structure providing industry-leading system performance and extensibility, supporting evolving service development requirements.


2013年12月11日星期三

Configuring a Single RRPP Ring the ME60

Create an RRPP domain and its control VLAN.
# Configure the domain of ME60A, the master node of ring 1, to be 1, and the ID of the major control VLAN to be 20.

<ME60A> system-view
[ME60A] rrpp domain 1
[ME60A-rrpp-domain-region1] control-vlan 20
[ME60A-rrpp-domain-region1] quit
# Configure the domain of ME60B, a transit node of ring 1, to be 1, and the ID of the major control VLAN to be 20.

<ME60B> system-view
[ME60B] rrpp domain 1
[ME60B-rrpp-domain-region1] control-vlan 20
[ME60B-rrpp-domain-region1] quit
# Configure the domain of ME60C, a transit node of ring 1, to be 1, and the ID of the major control VLAN to be 20.

<ME60C> system-view
[ME60C] rrpp domain 1
[ME60C-rrpp-domain-region1] control-vlan 20
[ME60C-rrpp-domain-region1] quit

Disable the STP function on the interfaces to be added to the RRPP ring.
# Disable the STP function on the interfaces to be added to the RRPP ring on ME60A.

<ME60A> system-view
[ME60A] interface gigabitethernet 2/0/1
[ME60A-GigabitEthernet2/0/1] undo shutdown
[ME60A-GigabitEthernet2/0/1] portswitch
[ME60A-GigabitEthernet2/0/1] stp disable
[ME60A-GigabitEthernet2/0/1] quit
[ME60A] interface gigabitethernet 2/0/2
[ME60A-GigabitEthernet2/0/2] undo shutdown
[ME60A-GigabitEthernet2/0/2] portswitch
[ME60A-GigabitEthernet2/0/2] stp disable
[ME60A-GigabitEthernet2/0/2] quit
# Disable the STP function on the interfaces to be added to the RRPP ring on ME60B.

<ME60B> system-view
[ME60B] interface gigabitethernet 2/0/1
[ME60B-GigabitEthernet2/0/1] undo shutdown
[ME60B-GigabitEthernet2/0/1] portswitch
[ME60B-GigabitEthernet2/0/1] stp disable
[ME60B-GigabitEthernet2/0/1] quit
[ME60B] interface gigabitethernet 2/0/2
[ME60B-GigabitEthernet2/0/2] undo shutdown
[ME60B-GigabitEthernet2/0/2] portswitch
[ME60B-GigabitEthernet2/0/2] stp disable
[ME60B-GigabitEthernet2/0/2] quit
# Disable the STP function on the interfaces to be added to the RRPP ring on ME60C.

<ME60C> system-view
[ME60C] interface gigabitethernet 2/0/1
[ME60C-GigabitEthernet2/0/1] undo shutdown
[ME60C-GigabitEthernet2/0/1] portswitch
[ME60C-GigabitEthernet2/0/1] stp disable
[ME60C-GigabitEthernet2/0/1] quit
[ME60C] interface gigabitethernet 2/0/2
[ME60C-GigabitEthernet2/0/2] undo shutdown
[ME60C-GigabitEthernet2/0/2] portswitch
[ME60C-GigabitEthernet2/0/2] stp disable

[Huawei ME60C-GigabitEthernet2/0/2] quit

2013年12月4日星期三

Obtaining Upgrade AR3260 Software

The system software of AR3260 V200R002C02SPC200 is AR3260-V200R002C02SPC200.cc.

Run the display version command in the user view to check the current system software version and ensure that it meets the upgrade requirement.
<Huawei>display version                                                         
Huawei Versatile Routing Platform Software                                     
VRP (R) software, Version 5.90 (AR3200 V200R002C02SPC100)                      
Copyright (C) 2011 HUAWEI TECH CO., LTD                                         
Huawei AR3260 Router uptime is 0 week, 0 day, 0 hour, 1 minute                 
BKP 0 version information:                                                     
1. PCB      Version  : AR01BAK3A VER.B                                         
2. If Supporting PoE : No                                                      
3. Board    Type     : AR3260                                                  
4. MPU Slot Quantity : 2                                                       
5. LPU Slot Quantity : 10                                                      
                                                                               
MPU 15(Master) : uptime is 0 week, 0 day, 0 hour, 1 minute                     
SDRAM Memory Size    : 2048    M bytes                                         
Flash Memory Size    : 16      M bytes                                         
NVRAM Memory Size    : 512     K bytes                                         
SD Card0 Memory Size : 1882    M bytes                                          
MPU version information :                                                      
1. PCB      Version  : AR01SRU3A VER.B                                         
2. MAB      Version  : 0                                                        
3. Board    Type     : SRU80                                                   
4. CPLD0    Version  : 104                                                     
5. CPLD1    Version  : 104                                                      
6. FPGA     Version  : 111                                                     
7. BootROM  Version  : 236                                                     
                                                                               
LPU 2 : uptime is 0 week, 0 day, 0 hour, 0 minute                              
SDRAM Memory Size    : 256     M bytes                                         
Flash Memory Size    : 16      M bytes                                         
LPU version information :                                                      
1. PCB      Version  : AR01SDCE2A VER.B                                        
2. MAB      Version  : 0                                                       
3. Board    Type     : 1E1/T1-M                                                
4. CPLD0    Version  : 100                                                     
5. BootROM  Version  : 203                                                     
                                                                                
FAN version information :                                                      
1. PCB      Version  : AR01DF05A VER.A                                         
2. Board    Type     : FAN                                                      
3. Software Version  : 104

In the preceding output, AR3260 V200R002C02SPC100 indicates the system software version currently running on the ME60. If this is the target version, no upgrade is necessary.

2013年12月3日星期二

UATool NE40E Usage Scenario

The UATool must be used to upgrade the  Huawei NE40E. The UATool can be used in three upgrade scenarios. Huawei recommends the first two scenarios. The third scenario, on-site upgrade, can be used if necessary. The three scenarios are described below:
  Remote upgrade with nearby support
Software commissioning engineers remotely upgrade the NE40E-X1/X2 from the network management center. Spare part provisioners wait near the site and are ready to deliver spare parts to the site quickly. Huawei recommends this scenario in the following situations:
−    The project is at the site deployment stage, and there are no stringent time requirements for replacing spare parts.
−    The spare part provisioning site is close to the upgrade site with favorable traffic and road conditions so that spare parts can be installed within the required time frame.
−    There are backup planes or links on the customer's network, and customer requirements allow enough time to install spare parts.
  Remote upgrade with on-site support
Software commissioning engineers remotely upgrade the NE40E-X1/X2 from the network management center. Spare part provisioners wait on site. Huawei recommends this scenario if spare parts cannot be delivered to the site within the required time frame.
  On-site upgrade
Software commissioning engineers upgrade the NE40E-X1/X2 on site. Spare parts are also available on site. This scenario can be used when only one site is being upgraded.
Huawei recommends that the upgrade is performed using the UATool. The UATool can automatically compare pre-upgrade services and post-upgrade services. This prevents operator errors during the upgrade and decreases upgrade risks.
In all the three scenarios, software commissioning engineers must be Huawei engineers with a good command of the NE40E-X1/X2 upgrade procedures. The personnel providing and replacing parts (who can be engineers from Huawei partners or customer staff) must be able to correctly identify product models and replace boards.
The three scenarios described above are examples of typical upgrade situations. Engineers can flexibly determine the way the upgrade is performed based on the real-world situation.

The NE40E-X1/X2 plays an important role on a network. Ensure that spare parts are available when using the UATool to upgrade the NE40E

How to Configuring IPoEoA Mapping on PVCs Huawei AR3200

Huawei AR3260 Series routers are designed to provide secure unified voice and data communication with exceptional performance and scalability to meet the demands of today’s enterprise requirements.
Run:
system-view
The system view is displayed.
Run:
interface virtual-ethernet interface-number
A VE interface is created and the VE interface view is displayed.
Run:
quit
The system view is displayed.
Run:
interface atm interface-number [.subinterface ]
The ATM interface or sub-interface view is displayed.
Run:
pvc { pvc-name [ vpi/vci ] | vpi/vci }
A PVC is created and the PVC view is displayed.
Run:
encapsulation { aal5snap | aal5mux }
The AAL5 encapsulation type is specified for the PVC.
The AAL5 encapsulation type can be aal5snap or aal5mux. The default value is aal5snap.
Run:
map bridge virtual-ethernet interface-number

IPoEoA mapping is AR3260 configured.