Configuring the GE/FE Optical/Electrical Interface

Generally, the ME60 sets an Ethernet interface to an optical or electrical interface based on the interface module's type. If the  Huawei ME60  cannot identify an interface module, you need to manually set the interface to the optical or electrical mode.

Run:

system-view

The system view is displayed.

Run:

interface { ethernet | gigabitethernet } interface-number

The Ethernet interface view is displayed.

Run:

port-type { copper | fiber-100 | fiber-1000 }

The interface type is set.

NOTE:

When an SFP module is being replaced, the configurations such as the loopback test, interface speed, auto-negotiation mode, and duplex mode on the interface are all restored to default ones. You need to reconfigure them on the interface.

After the port-type command is run, the configurations such as the loopback test, interface speed, auto-negotiation mode, and duplex mode on the interface are all restored to default ones. You need to reconfigure them on the interface.

The parameter copper can be configured in the port-type command only when an optical/electrical SFP module is installed.

fiber-100 cannot be set for interfaces on the 24-Port 1000Base-X-SFP Flexible Card E(BP51-E) subcard.

Confirming the GTL License

The file extension of a GTL license file is .dat, which is different from the file extension of a software license file.

NE40E-X3  &NE40E-X8  600R003C00 supports the GTL license. For details on the features that can be controlled by the GTL license, see "NE40E&80E V600R003C00 License Policy Guide." Before the upgrade, confirm whether a new GTL license is required for both the master MPU and slave MPU. If a new GTL license is required but not obtained, services controlled by the GTL license cannot be used.

After obtaining the GTL license, check whether the electronic serial numbers (ESNs) of MPUs are the same as those in the GTL license file.

<HUAWEI> display esn

ESN of master:030MDB108B000014

ESN of slave:030MDB108B000013

Compare the output of the above command with the ESN field in the GTL license file.

You can open a GTL license file with the notepad application to check whether the ESNs in the GTL license file are the same as those of the MPUs.

To use the license-controlled features in V600R003C00, you need to apply for the corresponding GTL license from Huawei's GTL platform before the upgrade.

After the MPU of the device is replaced, the original GTL license will support the new MPU for 60 days. After this period, if use of the new MPU continues, a new GTL license from Huawei is required.

Configuration Example of the RADIUS Authentication

The MA5616  is interconnected with the RADIUS server through the RADIUS protocol to implement authentication.

Configure the authentication scheme.
Configure authentication scheme newscheme (users are authenticated through RADIUS).
huawei(config)#aaa
huawei(config-aaa)#authentication-scheme newscheme
huawei(config-aaa-authen-newscheme)#authentication-mode radius
huawei(config-aaa-authen-newscheme)#quit
huawei(config-aaa)#quit
Configure the RADIUS protocol.
Create RADIUS server template template1. RADIUS server 10.10.66.66 functions as the primary authentication server, and RADIUS server 10.10.66.67 functions as the secondary authentication.
huawei(config)#radius-server template template1
 Note: Create a new server template
huawei(config-radius-template1)#radius-server authentication 10.10.66.66 1812
huawei(config-radius-template1)#radius-server authentication 10.10.66.67 1812 secondary
huawei(config-radius-template1)#quit
Create a domain.
Create domain isp1.
huawei(config)#aaa
huawei(config-aaa)#domain isp1
  Info: Create a new domain
Reference the authentication scheme.
You can reference an authentication scheme in a domain only after the authentication scheme is created.
huawei(config-aaa-domain-isp1)#authentication-scheme newscheme
Reference the RADIUS server template.
You can reference a RADIUS server template in a domain only after the RADIUS server template is created.
huawei(config-aaa-domain-isp1)#radius-server template1
huawei(config-aaa-domain-isp1)#quit

User1 in isp1 can be authenticated and can log in to the MA5620

Configuring the NE80E with 5000 W power consumption to Power on LPUF-40s/LPUI-40s

How to configure the NE40E-X3   with 5000 W power consumption to power on LPUF-40s/LPUI-40s.

Run:
system-view
The system view is displayed.
Run:
set board-power-on lower-performance-fan enable
The NE80E with 5000 W power consumption is configured to power on LPUF-40s/LPUI-40s.
Run:
system-view
The system view is displayed.
Run:
set power input-power power-value
The input power of the power module is configured.

NOTE:
This command can only be used on the NE80E with 5000 W power consumption, and does not need to be used on the NE40E-X8   with 8000 W power consumption.